home >
articles >
O.I.L.
An Origami Instruction Language
by John Smith
Note: The following is first section of John Smith's
booklet, An Origami Instruction Language, published by the British
Origami Society and is included here by permission from the author. Any
reproduction of this material by any means is prohibited without the
express consent of the author. For further information, please consult the
booklet and/or contact the
author. I have made every attempt to preserve the original flavour of
the text, making only such changes as were necessary to display this in
HTML form (including redrawing the diagrams). Joseph Wu.
Reference: Smith, John. An Origami Instruction
Language. B.O.S. Booklet No. 4, first published December 1975. ©
1975 by John S. Smith.
Our existing methods for writing down instructions for origami models
have both advantages and disadvantages. Amongst the advantages is that one
can quickly check one's progress against a picture of each stage and
identify a surface fold easily. The disadvantages are that it requires
considerable skill to prepare good drawings and they are expensive to
reproduce. Further, the present instructional system is not really precise
enough about the layers to be manipulated in a fold or the exact location
required for a fold. There is, therefore, a case for considering whether a
written language can be developed which does not depend upon the expertise
of a draughtsman and which is precise. As a byproduct such a language
will of necessity enable us to study more closely the structure of folds
and aid in classifying and identifying fold sequences and
complexities.
I presented an origami draft of such a language in my paper "The Nature
of Paper Folding" (Library reference J509, 1971). Since then I have
been developing the ideas and they are now at the point that I believe it
useful to publish the present state of the language and to see how members
feel about it. I must thank Simon Williams for his most valuable proposal
which enabled me to simplify some of the typical problems of representing
reverse folds.
The language has two parts which occur in each step.
 Definition matrix  a formal statement in rows and columns uniquely
identifying the points on the boundary or elsewhere of the model so far and
defining any new locations needed for the next fold/s. To a certain extent the
matrix can be used to check the accuracy of what has been folded so far.
 Fold Instructions  Usually these consist of identifying the two points
which are to be brought into coincidence by a fold (or folds). On occasions two
lines may be specified or a mixture of points and lines. It is always
assumed that the smallest number of creases will be made to flatten the
model with the coincidence as specified (e.g. one fold only if all layers are
involved). If necessary the line along which a fold is to be made can be
specified.
A Demonstration
Let us see how the language works to fold a preliminary fold. Here is the O.I.L.
for the fold.
Let us now translate:
Fold Instruction 
Commentary 
Square

( (1) is the step number )
This is the definition matrix. The boundary points are angles on the boundary
of flat model. We number them from top to bottom and left to right as we go.
The number by itself as in 1.2.3.4. indicates a right angle. (see (2) ). Thus
our square is arranged with a point uppermost. If points are in the same row
then the are exactly in the same line horizontally on the paper. If in
a column then they are exactly in line vertically.


Here is a fold instruction. It means put point 1 on to point 4 and make a
crease. The arrow shows a fold instruction. The number 1 over the
arrow means that the top layer only is involved (we count layers involved in
a fold from the top). As it is over the arrow it means put 1 on
top or over 4 i.e. a valley fold.


This line shows the end of a fold. Notice how each step consists of a
definition matrix followed by a fold (or folds).


Here is our second step and we start again with a definition matrix and each
time we start our numbering afresh.
The line above 1 and 2 indicates an angle less than 90 degrees (if it
was larger it would be shown as 1 or 2 for example). These
lines are called qualifiers.


Now our fold instructions: notice that as our numbering uniquely identifies a
boundary point we do not need to show the qualifiers again. Our first fold
says put point 1 to point 3. But we are required to fold between the
two layers of paper as shown by the arrow passing between layer
numbers. Therefore our top layer (=1) will be a mountain fold and our second
(lower layer) will be a valley fold. Therefore they appear as; 2 above the
arrow thus fold 1 over 3 (valley) for second layer; 1 is under the
arrow thus requiring us to put 1 under 3 for the first layer (mountain).
Clearly this is a reverse fold. Now repeat for the other side i.e. 2>3.
Simon Williams introduced the idea of folding into or between layers
which is typical of reverse or sink folds.

It may be worthwhile to spend a little more time on this particular
problem of folds made between layers  compared with folds made
with layer or layers treated as one as it is an important concept in the
language. Consider a square folded in half thus:


the line from (12) is bounded (it has no open edges at all  or if you
prefer only one edge). The rest of the boundaries have two edges.

If we write this down in O.I.L. we have
Now consider a fold This is a valley fold  all
layers together i.e. 2 is put over P. (See aboove diagram). Then
try which is a mountain fold with all layers together
(see above diagram). If we wish to fold but
between layers 1 and 2 we have a reverse fold.
Such a move involves a valley and mountain fold and the reversal of
the bounded line.
This might be appreciated more easily by cutting the line (1T). Now we
can make two separate folds.
If, however, we have the bounded line (1T) then this must be reversed.
Therefore the instruction
necessarily means in this case three folds to be simultaneously
manipulated as follows:
,
& the reversing of (1T)
In order to keep the language as compact and simple as possible the
instruction only is used because the mountain and
valley folds required by the coincidence of 1 to P can only be secured by
the reversal of the bounded layer. Remember the minimum number of folds to
achieve point coincidence is always assumed.



Shows end of fold.


